The next fire pit was designed by and built for Kevin Leys of Chicago. He did a great job and you decide.
Then it was framed for exterior plywood or you could use metal studs and wonder board.
This is a natural gas fire pit. It was tested as soon as it turned dark, fun!
Now we add the crushed lave rock and glass over that. There are many sub materials you can use as a filler. Just ask.
Now we start to apply the tile for the finishing touch.
The stainless steel pan burner below has a 24" stainless steel star burner installed and it is connected to our 110 volt electronic ignition. This is a propane burner.
We then covered it with our Starfire to test for soot and as you can see, a clean burn.
Our products do not require any certification from the AGA, CSA or UL as it is considered a stand-alone product by these agencies. We are told that we would need a certification if sand and or lava rock would need certification. The agencies are franchise operations and they are privately owned and they are not a government agency. These agencies are hired for mass production testing and AGA, CSA and or UL do not certify custom one of a kind projects. Custom burners need no certification as this only applies to production equipment. Just so you can understand that a certification costs about $15,000.00 and certification was developed for production/ mass production to assure quality. Any parts that would normally need AGA or UL do in fact have these approvals. Parts with function need and should have some sort of approval. The pan burners we sell that do have UL, CSA and or any other listings are produced by other companies. The custom pan burners that we produce are just that, custom. Therefore do not require UL, CSA and or any other agency listings as these are custom. The parts that we use to build these pans are UL, CSA listed as they should be. We would never use any “Third World Country” or any unlisted, untested parts to build any products and or parts to endanger any product performance what so ever.
The fire pit below is in San Francisco California. They use one of out FPPK units.
Here you can see the simple construction.
A local artist made the glass inlay top. Very cool!
We supplied the FPPK and the Clear glass
The burner below is one of our FPPK's (fire pit propane kit). With this FPPK we set it up for Black Magic! This was table tested for the pictures. Hopefully the customer will send us pictures after and during installation. We first sent these pictures for the customers approval. Here you go! The pan below belongs to Scott Spector and he finally installed the fire pit in his back yard, WOW, one really nice backyard!
This is one of our propane pan burner with slight modifications.
As you can see around the lower edges it was leaking and yes we did fix this.
The fire pit below was built by Scott Spector in Florida. He started with an FPPK 30 which includes a 30" base plate and a double 24" stainless steel ring. Here we go from the beginning:
The propane line was run/ installed under the pavers.
The colors that were used are
1/2" Clear base,
Black Magic in the center,
Cobalt Blue Topper,
Cobalt Blue Light Topper
and our FPPK 30". That is our 30" propane burner. You can see the actual burner above burning before shipment and installation.
We don't have any pictures of the fire pit burning at Scott's but he did tel us that when he fired it up again he would try to send us a few pictures. Thanks Scott.
The fire table below was built by Christina "Stina" in the San Francisco area. With a little ambition, imagination and our help, she now has one very nice fire table.
Here is where it started. She made a template of the pan and where the mounting tabs would be located. Then we built the aluminum pan and propane burner for Stina to install.
Below is how the teak table started. We just brought it into the future.
Below the pan was installed with Galaxy Green base glass.
Below you can see the top installed and what a difference.
Below is her wonderfully finished project, Great job Stina!
The Fire Table below was installed in Sacramento California by and for Yard Crashers. The finished pictures will be posted on the Yard Crashers page when this project is installed after 01 20 10. This episode was to be labeled "Outdoor Shower" on HGTV and the DIY Network but somehow it was labeled "Modern Fire Wall" go figure? It is episode 302 on HGTV or DIY Network. The details will be shown on the DIY page when and as soon as we receive them from the producers. We built a square aluminum pan with an 18" double stainless steel ring and used one of our FPPK kits for the propane fuel. This will be shown on the episode coverage as well. Here are the pictures of the back yard and the finished fire table using propane.
The propane burner conversion below was performed by Richard King of South Carolina.
Richard has one very cool Super Bowl party room! We assisted him in converting a propane fire pit one very nice clean burning fire pit. We will explain as we move along.
Richard: You did a beautiful job on your gazebo!
Here is the fire pit turned up so you can see that we installed one of our FPPK (fire pit propane kit) The tank was under the deck.
Richard may of had a few flex lines that were a bit too long.
It's supposed to look simple when it's finished.
The controls were adapted to his and over his old controls.
Above is on low and I might add no black soot or smoke! You would think the manufactures of these tables would of figured it out by now?
Below is the standard ring but we installed thermo coupler and safety pilot kit.
Below is what were sent to convert. Small flames and no air mixer what so ever. Just a lot of soot and black smoke, seen it before?
Below, not a lot of flame is there? The reason is once they turn it up for you, the soot starts to show. So they tell you it can't be turned up.
Now we step in, air mixed calibrated to the ring and valve system and pilot light and thermo coupler in place.
and turbo high and still with a clean burn!
and below is the 2009 Super Bowl Party! Thanks Richard!
Yes, we can convert anything!
The wine barrel below was build by one of our newer dealers in Texas. Matt's Custom Welding. Contact us for information about Matt's wonderful work. We are going to be much more of Matt's work and look around his showroom in the pictures below. Many more projects to come.
There was a steel bowl installed using our propane system to burn our glass. They used Bronze base glass in the fire pit.
Propane Burner Issues
I have seen this scenario all too often. The supplier that you have purchased from only cared about making the sale of the glass. They did not ask what you were doing. How you were doing it. What you were working on, etc. etc. etc. They did not ask if you had propane or natural gas or if you had natural gas close by to use opposed to propane. You are now finding out that there is no customer support after the sale. We are the only manufacture building one propane burner at a time to suit your needs. We care from beginning to end and more importantly after the fact! We offer customer support FOREVER!
Let me tell you how we feel about these other companies selling products they know nothing about:
You purchased a Ford and now you are going to the Chevrolet dealer for advice and parts on how to fix the problems. That is not how it works. You need you to put pressure on the company that sold you the product that does not perform as you thought it should. We will and or can resolve your issues, but you need to make sure these companies stop selling products they know nothing about.
Have you contacted the company that you purchased from?
Have you received any advice from this company on how to resolve the issue?
Are they even concerned about your problems?
Did you disclose to this company what you were working on?
Did this company ask for details about your project?
Have you asked if you can return all of the parts and products because of product failure?
Does this company even have any information online about their success on propane burners?
Did you receive any customer support?
Does the company you purchased from even have a physical address where you can visit?
We do genuinely feel bad for the customer being taken advantage of by companies such as these, selling parts and supplies, which they know nothing about.
Please keep us posted on your developments so we may continue to remedy your situation. We are proud of our creations, inventions, customer support, product lines as we do all of this for you, the customer!
Ed Jaunzemis President, Moderustic Inc
Here is the answer some of you think you know. (You don't!) These are Air Mixers, Venturis Carburetors.
These like a carburetor on any engine act as the air fuel mixture governor. Have you ever been behind an older car that smells funny? Wrong air mixture! Bad mechanic! The air mixers have to be calibrated not only to the valving but the burner as well. We have been building propane burners for several years now and we have never had an issue with any configuration that we have built, ever. It's the same as porting an engine for proper air flow. If you just STICK one of these on your burner then you may be giving us a call soon enough.
Here are a few pictures of the 1/2" and 3/4" air mixers, (40,000 to 400,000 btu mixers).
If you attach it and create back pressure, you will have a fire or an explosion, guaranteed. We are not trying to frighten you but to make you aware. We believe in safety first and we don't build systems without thermo couples and or pilot light systems, ever!
As you may have of seen on our "How Not To Do It Page" they still screw up no matter how hard they try. We are here only to help!
he next Wine Barrel Fire Pit was built be Shaun Ibe.
We supplied all of the parts, knowledge base and Shaun built one really nice Wine Barrel Fire pit! We will explain as we move forward
Shaun used up all of his old corks to line the top with and then he had a piece of glass made to cover the corks. Be sure you have the top made with tempered glass! Teh glasss that was used was
1/4" Clear Base Glass
Platinum Base Glass
Gold Ruby Topper
See the Wine Barrel Parts Page!
We supply you with creativity, parts, support, imagination and give you license to be creative on your own, after all, that's what we do and who we are!
"CLICK HERE" or on the pictures below to see what John Lehman did and how he built this table!